ユーザーズガイド AIRLIVE WLA-9000AP QUICK SETUP GUIDE

[. . . ] 2. NO T E NO T E 38 3. NO T E NOTE NO T E 1. 2. 2 NO T E 4 3 1 1 2 3 39 4 NOTE NO T E 1. 2. 1 4 3 2 1 NOTE 2 3 40 4 SCENE HOME UTILITY LEVEL MUTE CANCEL ENTER 41 Info Label Version Date Battery Net MASTER/SLAVE IP Adr. Disp LCD Contrast LCD Backlight Meter Fall Time Lock Utility Panel Lock Boot Panel Lock Target User Defined Lock Misc Scene Store Last Mem. Resume Event Scheduler Internal HA Ctrl Remote WCLK Fs Int WCIN Cascade SLOT1-4 Slot Card Name Format MIDI Port DAW CH Program Change Control Change Param Change GPI Reset Max Min HA HA WCLK Gain +48V Frq 42 CASCAD Head Margin Check 43 3 1. [. . . ] Saving Failed Slots Overloaded Store Disable Storing Failed Used by ExDevice 56 Used by HA Ctrl Used by MIDI Cable Disconnect Cannot be assigned Cannot Store — CAS. Out Sync Err Connection to Master DME is Lost Connection to Slave DME is Lost Download Success Downloading Do not turn off DSP Power Shortage — — Duplicate IP Adr. Err: Wrong Device Group Settings Executing File Opening Do not turn off Illegal MAC Adr. Network Busy — — Network Error Network Setup No Current Scene — No MAC Adr. 57 Panel Locked Panel Unlocked Recovering Do not turn off — Saving HA Info Do not turn off Saving Setup Info Do not turn off Scene Recalling Do not turn off Scene Storing Do not turn off Searching for Master DME Unit. . . SLOT1 Sync Err — — — — — — SLOT2 Sync Err SLOT3 Sync Err SLOT4 Sync Err Synchronizing Do not turn off Updating Do not turn off Used by ExDevice — — Used by HA Ctrl Used by MIDI WCLK Unlocked WCLK In Sync Err 58 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 59 Sampling Frequency Internal External 44. 1kHz, 48kHz, 88. 2kHz, 96kHz Normal Rate: 39. 69 – 50. 88kHz Double Rate: 79. 39 – 101. 76kHz DME64N: 0. 85 msec (Input of MY8-AD96 to Output of MY8-DA96) DME24N: 0. 5 msec ([IN] port to [OUT] port) 16 (depends on size of data) 999 (depends on size of data) 160 x 64 dot matrix LCD with backlight 7-segment LED x 3 Signal Delay (Fs = 96kHz) Memory Display Scene No. Indicators Configuration Scene Wordclock External Control Analog Input*1 Analog Output*1 EXT. CLOCK, 96kHz, 88. 2kHz, 48kHz, 44. 1kHz NETWORK, MIDI SIGNAL x 8, PEAK x 8 SIGNAL x 8, PEAK x 8 DME64N: 80W DME24N: 75W DME64N: 480 x 145 x 411. 5mm, 3U DME24N: 480 x 101 x 411. 5mm, 2U DME64N: 9. 5kg DME24N: 8kg Zone Configuration MASTER Power Consumption Dimensions (W x H x D) Weight Temperature Range AC Power Cord Length Supplied Accessories Free-Air operating Storage 10 – 35 °C -20 – 60 °C 2. 5m AC power cord, AC plug adaptor, Owner’s Manual, AC plug clamp, 16-pin Euroblock plug x 2, 8-pin Euroblock plug x 4 (DME64N), 3-pin Euroblock plug x 16 (DME24N), Warranty card *1. Available on DME24N only 60 DME24N ANALOG INPUT CHARACTERISTICS Terminals Gain Actual Load Impedance 3kΩ Total Harmonic Distortion fs=96kHz Input Connector Euroblock CH INPUT 1–8 For Use With Nominal 50 – 600Ω Mics & 600Ω Lines Input Level Max. Nominal before clip -60dBu (0. 775mV) +10dBu (2. 451V) -40dBu (7. 75mV) +30dBu (24. 511V) Output CH OUTPUT 1–8 RL 600Ω Conditions GAIN = -60dB @20Hz – 20kHz @+14dBu GAIN = +10dB @20Hz – 20kHz @+14dBu -30dBFS @1kHz, phones level control: max. Min. Typ. Max. 0. 1 Units % CH INPUT -60dB 1–8 +10dB • 0dBu = 0. 775 Vrms. • • 0. 05 % Internal OSC PHONES 8Ω 0. 1 % Hum & Noise EIN = Equivalent Input Noise Input Output CH OUTPUT 1–8 RL 600Ω Conditions GAIN = -60dB Master fader at nominal level and one Ch fader at nominal level. (Mixer mode) GAIN = +10dB Master fader at nominal level and one Ch fader at nominal level. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 12 Only use attachments/accessories specified by the manufacturer. [. . . ] Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. [. . . ]