ユーザーズガイド ASUS CUV266

[. . . ] ® FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Re-orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING!Any changes or modifications to this product not expressly approved by the manufacturer could void any assurances of safety or performance and could result in violation of Part 15 of the FCC Rules. Reprinted from the Code of Federal Regulations #47, part 15. 193, 1993. Washington DC: Office of the Federal Register, National Archives and Records Administration, U. S. [. . . ] Frequency Multiple CUV266 0 1 0 1 0 1 FREQ_SEL ON OFF 1 2 3 4 5 Jumper Mode Jumper Free (Default) 1 2 2 3 CUV266 Jumper Mode Setting JEN CUV266 FREQ_SEL 0 1 0 1 0 1 ON 1 2 3 4 5 ON 1 2 3 4 5 ON 1 2 3 4 5 ON 1 2 3 4 5 (JumperFree Mode) CPU AGP PCI 66MHz 66MHz 33MHz 100MHz 67MHz 33MHz 133MHz 66MHz 33MHz CUV266 CPU External Frequency Selection CUV266 0 1 0 1 0 1 ACRUSB2 ACRUSB1 1 2 2 3 CUV266 ACR/USB Selection Use External USB 2&3 (Default) Use ACR USB CUV266 0 1 0 1 0 1 LAN_EN 1 2 Enable (Default) 2 3 Disable CUV266 LAN Setting CUV266 0 1 0 1 0 1 Disable Onboard Audio Codec 1 2 Enable Onboard Audio Codec (Default) AUDIO_EN 2 3 CUV266 Audio Codec Setting CUV266 USB01_PWR USB23_PWR USB45_PWR 1 2 +5V (Default) 2 3 +5VSB CUV266 USB Device Wake Up 0 1 0 1 0 1 VIO3 CUV266 1 2 0 1 0 1 0 1 2 3 3 4 2. 65V (Default) 2. 75V 2. 9V VIO2 1 2 2 3 3 4 CUV266 VIO Setting 2. 65V (Default) 2. 75V 2. 9V CUV266 0 1 0 1 0 1 Lithium Cell CMOS Power CR2032 3V CLR_RTC Short jumper to clear CMOS CUV266 Clear RTC RAM CUV266 CUV266 184-Pin DDR DIMM Sockets 0 1 0 1 0 1 CUV266 0 1 0 1 0 1 Pentium III Gold Arrow CUV266 Socket 370 CUV266 AGP Card without Retention Notch 0 1 0 1 0 1 TOP VIEW 20-pin bay Rib (inside slot) 28-pin bay Rib CUV266 Accelerated Graphics Port (AGP PRO) CUV266 CUV266 Advanced Communication Riser (ACR) 0 1 0 1 0 1 PS/2 Mouse (6-pin Female) PS/2 Keyboard (6-pin Female) RJ45 USB 0 Universal Serial Bus (USB) 1 Parallel Port (25-pin Female) COM1 COM2 Serial Ports (9-pin Male) Joystick/Midi (15-pin Female) Line Out Line In Mic 1/8" Stereo Audio Connectors CUV266 0 1 0 1 0 1 IDELED TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. CUV266 IDE Activity LED CUV266 0 1 0 1 0 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1 PIN 1 CUV266 Floppy Disk Drive Connector CUV266 0 1 0 1 Secondary IDE Connector PIN 1 0 1 Primary IDE Connector NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. CUV266 IDE Connectors CUV266 IMPORTANT: Requires an ATX power supply with at least 720mA +5 volt standby power. 0 1 0 1 0 1 WOL_CON +5 Volt Standby PME Ground CUV266 Wake-On-LAN Connector CUV266 0 1 0 1 0 1 WOR RI# 2 Ground 1 CUV266 Wake-On-Ring Connector 0 1 0 1 0 1 0 1 0 1 0 1 CUV266 CUV266 CUV266 Front Panel USB Headers CUV266 12-Volt Cooling Fan Power 6 GND +12V Rotation GND +12V Rotation 1 PWR_FAN CPU_FAN CHA_FAN USB2_3 USB4_5 USB Power USBP3– USBP3+ GND USB Power USBP2– USBP2+ GND NC 5 GND +12V Rotation 10 CUV266 IRRX GND IRTX +5V (NC) Standard Infrared (SIR) Front View Back View SIR CIR 0 1 0 1 0 1 CIRRX CIR+5V CIRTX GND IRTX GND IRRX +5V (NC) CUV266 Infrared Module Connector CUV266 0 1 0 1 0 1 CHASSIS CUV266 Chassis Open Alarm Lead CUV266 +12. 0Volts +5V Standby Power Good Ground +5. 0 Volts Ground +5. 0 Volts Ground +3. 3 Volts +3. 3 Volts +5. 0 Volts +5. 0 Volts -5. 0 Volts Ground Ground Ground Power Supply On Ground -12. 0Volts +3. 3Volts CUV266 ATX Power Connector 0 1 0 1 0 1 CUV266 0 1 0 1 0 1 SMB 1 CUV266 SMBus Connector Ground SMBDATA +5V SMBCLK CUV266 Audio Panel Connector AAPANEL MIC2 AGND Line in_L AGND2 Line in_R MICPWR Line out_L AGND3 Line out_R CUV266 Front Panel Connectors 0 1 0 1 0 1 0 1 0 1 0 1 CUV266 CUV266 SIR CIR NC GND NC CIRRX +5VSB +5 V IRRX GND IRTX NC GND NC CIRRX +5VSB CHASSIS# EXTSMI# +5V MLEDPCIRST# BATT NC +5 V IRRX GND IRTX SMBDATA +3VSB SMBCLK LOCKKEY NC NC IR_CON AFPANEL Standard Infrared (SIR) Front View Back View IRTX GND IRRX +5V (NC) CD (Black) AUX (White) Left Audio Channel Ground Right Audio Channel MODEM Modem-Out (from Modem) Ground Modem-In (to Modem) MIC2 1 CUV266 Internal Audio Connectors CUV266 Internal Microphone Connector CUV266 CUV266 MIC Power MIC Input Ground Left Audio Channel Ground Right Audio Channel 3 0 1 0 1 0 1 0 1 0 1 0 1 CUV266 0 1 0 1 0 1 HPHONE 1 CUV266 True-Level Line Out Header CUV266 0 1 0 1 0 1 JTPWR Power Supply Thermal Sensor CUV266 Thermal Sensor Connector HP OUT LT GND HP OUT RT CUV266 Digital Audio Interface Output Ground CUV266 Smartcard 0 1 0 1 0 1 0 1 0 1 0 1 CUV266 CUV266 1 VCC NC SCRFET# SCRCLK RFU1 GND NC2 LED NC SCRREST RFU2 SCRUI SCRRES# SPDIFOUT CDSPDIFIN Input Ground CUV266 * Requires an ATX power supply. IDE LED PLED IDELED+ IDELED- Speaker Connector +5V Ground Ground SPKR 0 1 0 1 0 1 Power LED +5 V Message LED +5 V MLED ExtSMI# Ground PWR_SW Ground SMI Lead ATX Power Switch* CUV266 System Panel Connectors ResetCon Ground Reset SW Master/Slave Drives LAN Activity Output Signal LEDs Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other Top: Codec PHONE Bottom: LINE Crystal [. . . ]