ユーザーズガイド KYOSHO CALMATO TR

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. v vi vii viii ® ® ® (ICH5) - 2 x UltraDMA 100 - 2 x Serial ATA ix x ® ® ® ® 1-2 ® ® ® 1-3 1-4 1. Use [+] or [-] to configure system time. +Tab F1 F10 ESC Select Screen Select Item Change Field Select Field General Help Save and Exit Exit 2-10 Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20. 0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : 4 Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported Type LBA/Large Mode Block (Multi-sector Transfer) PIO Mode DMA Mode Smart Monitoring 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] Select the type of device connected to the system. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-11 IDE Configuration Onboard IDE Operate Mode Enhanced Mode Support On IDE Detect Time Out (Sec) [Enhanced Mode] [S-ATA] [35] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-12 2-13 AMI BIOS Version : 08. 00. 09 Build Date : 05/13/03 ID : CALMATO TR063 Processor Type Speed Count : Intel(R) Pentium(R) 4 CPU 2. 40GHz : 1800 MHz : 1 Select Screen Select Item Change Option General Help Save and Exit Exit System Memory Size : 256MB +F1 F10 ESC 2-14 Jumperfree Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP USB Configuration Configure CPU. Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit Configure System Frequency/Voltage AI Overclock Tuner CPU Ratio [Standard] [12] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-15 Configure System Frequency/Voltage AI Overclock Tuner CPU External Frequency (MHz) CPU Ratio DRAM Frequency AGP/PCI Frequency (MHz) CPU VCore Offset to . IV DDR Reference Voltage AGP VDDQ Voltage [Manual] [100] [12] [Auto] [Auto] [Disabled] [Auto] [1. 50V] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-16 Configure advanced CPU settings Manufacturer Brand String Frequency : Intel(R) : Intel(R) Pentium(R) 4 CPU 2. 4GHz : 1800 MHz Ratio Status : Locked Ratio Actual Value : 18 CPU Ratio Hyper Threading Technology [18] [Enabled] Select Screen Select Item Change Option General Help Save and Exit Exit +F1 F10 ESC 2-17 Advanced Chipset settings WARNING: Setting wrong values in the sections below may cause system to malfunction. Configure DRAM Timing by SPD Memory Acceleration Mode DRAM Idle Timer DRAm Refresh Rate Graphic Adapter Priority Graphics Aperture Size Spread Spectrum ICH Delayed Transaction MPS Revision [Enabled] [Auto] [Auto] [Auto] [AGP/PCI] [ 64 MB] [Enabled] [Enabled] [1. 4] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-18 2-19 OnBoard AC’97 Audio OnBoard LAN OnBoard LAN Boot ROM Serial Port1 Address Serial Port2 Address Parallel Port Address Parallel Port Mode ECP Mode DMA Channel Parallel Port IRQ OnBoard Game/MIDI Port [Auto] [Enabled] [Disabled] [3F8/IRQ4] [2F8/IRQ3] [378] [ECP] [DMA3] [IRQ7] [Disabled] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-20 2-21 Advanced PCI/PnP settings WARNING: Setting wrong values in the sections below may cause system to malfunction. A device enclosed in parenthesis has been disabled in the corresponding type menu. Select Screen Select Item Change Option General Help Save and Exit Exit +F1 F10 ESC 2-29 Boot Settings Configuration Quick Boot Add On ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Typematic Rate Boot to OS/2 Wait for ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Force BIOS] [On] [Auto] [Fast] [No] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-30 Security Settings Supervisor Password User Password Change Supervisor Password Boot Sector Virus Protection [Disabled] Not Installed Not Installed <Enter> to change password. <Enter> again to disable password. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-31 Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection Installed Not Installed [Full Access] [Setup] [Disabled] <Enter> to change password. <Enter> again to disable password. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-32 2-33 Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. [. . . ] <Enter> again to disable password. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-31 Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection Installed Not Installed [Full Access] [Setup] [Disabled] <Enter> to change password. <Enter> again to disable password. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 2-32 2-33 Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. [. . . ]