ユーザーズガイド ROLAND SRA-200E

[. . . ]  01677290 ‘02-6-A2-51K 2 3 4 1 2 3 4 5 5 5 4 7 6 OUTPUT 1 3 INPUT 2 2 3 1 1:GND 2:HOT 3:COLD GND(SLEEVE) GND(SLEEVE) HOT(TIP) HOT(TIP) COLD(RING) GND HOT COLD COLD HOT GND 6 7 8 9 2 3 T R S 1 2 3 HOT COLD GND S T R 1 HOT COLD GND 10 2 3 T R S 1 HOT COLD GND HOT COLD GND 11 12 13 14 15 16 430 39. 8 6. 5 25 331 482 7. 5 44 48. 6 17 For EU Countries This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. (About the Protection Circuits → p. 12) 5 Rear Panel 5 4 7 INPUT 6 OUTPUT 1 3 INPUT 2 1. INPUT Connector (XLR-3-31 Type) * The pin assignment for the XLR type connectors is as shown below. Before making any connections, make sure that this pin assignment is compatible with that of all your other devices. 2 3 1 1:GND 2:HOT 3:COLD 2. INPUT Jack (TRS Standard Phone Type) Connect using quarter-inch TRS phone type when input is balanced, and connect with quarter-inch phone type when the input is unbalanced. * Check the pin assignments of other devices before connecting. GND(SLEEVE) GND(SLEEVE) HOT(TIP) HOT(TIP) COLD(RING) Quarter-inch TRS Phone Type (Balanced) Quarter-inch Phone Type (Unbalanced) 3. INPUT Terminals * Check the pin assignments of other devices before connecting. When making connections, be careful to avoid losing the screws that you remove. GND HOT COLD COLD HOT GND 6 4. INPUT LEVEL Switch This switches the input sensitivity (+4 dBm/-10 dBm). Select the setting appropriate for use with your system. MODE Switch Switches the unit between the STEREO and BTL modes. Select the mode that is appropriate for your configuration ( → p. STEREO : Channel A and Channel B work independently of each other. In this mode, the amp functions as a standard power amplifier. BTL : Channel A and Channel B are bridged internally, creating a 300 watt (8 ohms) mono power amplifier. Speaker Connection Terminals (Binding Posts) These are terminals for connecting speakers. * To avoid the risk of electric shock, do not touch the terminals while the amp is on. Please refer to "Precautions When Connecting and Switching on the Power". Cooling Fan/Air Vent This comprises a forced-air cooling fan in combination with air vents. Cooler air is drawn in through the intakes in the top and bottom panels, and the air heated by the amp is expelled through the vents. [. . . ] 1. k. l 107 564 Moscow, RUSSIA TEL: (095) 169 5043 SAUDI ARABIA aDawliah Universal Electronics APL Corniche Road, Aldossary Bldg. , 1st Floor, Alkhobar, SAUDI ARABIA P. O. Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081 BELGIUM/HOLLAND/ LUXEMBOURG Roland Benelux N. V. Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811 SPAIN Roland Electronics de España, S. A. Calle Bolivia 239, 08020 Barcelona, SPAIN TEL: (93) 308 1000 SYRIA Technical Light & Sound Center Khaled Ebn Al Walid St. 47, P. O. BOX 13520, Damascus, SYRIA TEL: (011) 223-5384 Roland Shanghai Electronics Co. , Ltd. [. . . ]