ユーザーズガイド ASUS P4T

[. . . ] ® FCC & DOC COMPLIANCE This device complies with FCC Rules Part 15. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Re-orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING!Any changes or modifications to this product not expressly approved by the manufacturer could void any assurances of safety or performance and could result in violation of Part 15 of the FCC Rules. Reprinted from the Code of Federal Regulations #47, part 15. 193, 1993. Washington DC: Office of the Federal Register, National Archives and Records Administration, U. S. [. . . ] Frequency Selection SW1 OFF 1 2 3 4 5 6 7 8 9 10 ® P4T Jumper 1 2 ON JumperFree 2 3 P4T JumperFree™ Mode Setting JEN USBPWR ® 1 2 Enable 2 3 Disable (Default) P4T P4T USB Device Wake Up 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 ON ON ON CPU/DRAM → 100. 0MHz 103. 0MHz 105. 0MHz PCI BUS → 33. 3MHz 34. 3MHz 35. 0MHz 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 108. 0MHz 36. 0MHz 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 ON ON ON ® CPU/DRAM → 110. 0MHz 112. 0MHz 115. 0MHz PCI BUS → 36. 7MHz 37. 3MHz 38. 3MHz 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 118. 0MHz 39. 3MHz P4T P4T CPU External Frequency Selection ON ON ON CPU/DRAM → 120. 0MHz 122. 0MHz 125. 0MHz PCI BUS → 40. 0MHz 40. 7MHz 41. 7MHz 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 128. 0MHz 42. 7MHz ON CPU/DRAM → 130. 0MHz 133. 0MHz PCI BUS → 43. 3. 0MHz 44. 3MHz ON ON ON ON 1 2 3 4 5 6 7 8 9 10 SW1 P4T CPU External Clock (BUS) Frequency Selection ON P4T ® SW1 ON 13. 0x 14. 0x 15. 0x 16. 0x 8. 0x 1 2 3 4 5 6 7 8 9 10 ON 1 2 3 4 5 6 7 8 9 10 ON 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 ON 1 2 3 4 5 6 7 8 9 10 9. 0x 10. 0x ON 1 2 3 4 5 6 7 8 9 10 ON 1 2 3 4 5 6 7 8 9 10 ON 1 2 3 4 5 6 7 8 9 10 ON 1 2 3 4 5 6 7 8 9 10 11. 0x 12. 0x a. C-RIMM 128MB RDRAM C-RIMM 128MB RDRAM RIMMB2 RIMMB1 RIMMA2 RIMMA1 b. 128MB RDRAM C-RIMM 128MB RDRAM C-RIMM RIMMB2 RIMMB1 RIMMA2 RIMMA1 c. 128MB RDRAM 128MB RDRAM 128MB RDRAM 128MB RDRAM RIMMB2 RIMMB1 RIMMA2 RIMMA1 Channel B Channel A RIMMB2 RIMMB1 RIMMA2 RIMMA1 RIMM Sockets ® RIMM with Heat Spreader C-RIMM P4T P4T 184-Pin RIMM Sockets MOUNTING NOTCH RDRAM (with heat spreader) NOTCH KEYS CONNECTORS (TOP VIEW) EJECTOR RIBS (inside socket) ® Pin 1 P4T Pentium 4 Processor Gold Arrow Pin 1 P4T Socket 423 Rubber Pad Metal Baseboard 2 Metal heatsink retaining clips 4 Copper captive nuts 4 Washers 4 Pan Head screws 2 Heatsink support bases Rubber Pad Metal Baseboard Copper captive nut Mothe rboard 9=IDAH ® Mo oa b r e th rd Washer 1 2 3 2 1 AGP Card without Retention Notch ® TOP VIEW P4T 20-pin bay Rib (inside slot) 28-pin bay Rib P4T Accelerated Graphics Port (AGP PRO) PS/2 Mouse (6-pin Female) PS/2 Keyboard (6-pin Female) Parallel Port (25-pin Female) COM1 COM2 Serial Ports (9-pin Male) USB 1 USB 2 RJ-45 Port Secondary IDE Connector Primary IDE Connector PIN 1 ® NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. P4T P4T IDE Connectors FLOPPY PIN 1 ® NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. P4T P4T Floppy Disk Drive Connector GND +12V Rotation Rotation +12V GND ® MAIN_FAN CPU_FAN (for power supply fan) Rotation +12V GND PCI_FAN (for chassis fan) P4T P4T 12-Volt Cooling Fan Power ® P4T 1 SMB P4T SMBus Connector ® 1 P4T CHASSIS P4T Chassis Open Alarm Lead Chassis Signal GND +5VSB_MB Ground SMBDATA +5V SMBCLK IMPORTANT: Requires an ATX power supply with at least 720mA +5 volt standby power ® WOL Ground PME +5 Volt Standby P4T P4T Wake-On-LAN Connector ® Ring# Ground P4T 2 1 P4T Wake-On-Ring Connector WOR 10 ® 6 1 5 1: USB Power 2: USBP2– 3: USBP2+ 4: GND 5: NC 6: USB Power 7: USBP3– 8: USBP3+ 9: GND USB2 P4T P4T USB Headers ® TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. P4T HDDLED P4T Hard Disk Drive Activity LED ® + P4T 1 P4T SCSI LED Connector SCSILED ® IR +5V (NC) IRRX GND IRTX Front View Back View 1 IRTX GND IRRX +5V (NC) P4T P4T Infrared Module Connector TR2 Thermal Sensor Connector ® P4T P4T Thermal Sensor Connector ATXPWR Pin 1 +3. 3VDC +3. 3VDC COM +5VDC COM +5VDC COM PWR_OK +5VSB +12VDC +3. 3VDC -12VDC COM PS_ON# COM COM COM -5VDC +5VDC +5VDC ® COM +12V DC P4T Pin 1 COM +12V DC Pin 1 Key COM +3V P4T ATX & Auxiliary Power Connectors AUXPWR +5V ATX12V Keyboard Lock Power LED PLED Keylock Ground +5 V Speaker Connector +5V Ground Ground Speaker ® +5 V MLED ExtSMI# Ground PWR Ground Message LED P4T Reset SW ATX Power Switch* SMI Lead * Requires an ATX power supply. P4T System Panel Connectors Reset Ground ® Intel I/O Controller Hub (ICH2) CLRTC Short solder points to Clear CMOS P4T P4T Clear RTC RAM LAN Activity Output Signal LEDs Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other [. . . ]