ユーザーズガイド DENON SC-T55XG

[. . . ] Consult the amplifier's instructions. • Clipping or other problems may occur in the output waveform when using the speaker systems with a high output and the amplifier's tone controls set to the maximum. Avoid using them under these conditions. • Never play such special signals as a tape recorder's fastforwarding signals or sine waves continuously. [. . . ] • Also note that if there is a magnet or any device generating magnetic force nearby, interaction between this device and the speaker systems can cause the colors on the TV to become blotchy. WARNING • For your safety, do not put anything nor lean yourself on the loudspeakers. • Do not push the loudspeaker from aside to protect it from topping that may cause serious accident. • Fix cord to prevent being caught on it and making loudspeakers topping down. Speaker system (SC-A55XG) • When setting on a shelf, etc. , attach the three included anti-slip pads (pieces of cork 2 mm thick) to the bottom. (Refer to diagram below. ) Anti-slip pad Anti-slip pad Screw holes Floor-mount stand (ASF-A77) / Ceiling suspension bracket (ASG-20) (When mounting on a stand or brackets) The speaker system (SC-A55XG) can be mounted to a separately sold floor-mount stand (ASF-A77) using the screw holes on the bottom (60 mm intervals) or to a ceiling suspension bracket (ASG-20) using the screw holes on the back (60 mm intervals). When mounting on a stand or bracket, follow the instructions included with the bracket or stand and be very careful to mount the speaker system securely. Never utilise a separately sold bracket ASG-10. Speaker system (SC-C55XG) • The included anti-slip pads or base can be used to set the speaker systems (SC-A55XG) at one of three angles: level, slanting upward ( at about 10 ) or slanting downward ( at about 10 ). To set the speaker system level Attach the three included anti-slip pads (pieces of cork 2 mm thick) to the bottom. (Refer to diagram below. ) In this case, do not use the included base. Speaker system (SC-C55XG) Bottom view Anti-slip pad To set the speaker system at an angle slanting upwards Use the included base and set as shown on the diagram below. In this case, do not use the three included anti-slip pads (pieces of cork 2 mm thick). Speaker system (SC-C55XG) Side view Included base Speaker system (SC-C55XG) Front view Included base To set the speaker system at an angle slanting downwards Use the included base and set as shown on the diagram below. In this case, do not use the three included anti-slip pads (pieces of cork 2 mm thick). Speaker system (SC-C55XG) Side view Included base Speaker system (SC-C55XG) Front view Included base CAUTION • Use the included base and set in a firm stable place. • If the speaker system is set in an unstable place, it could tip over or fall, possibly resulting in serious accidents. Speaker system (SC-T55XG) • When using the speaker system on a slippery surface (for example on tiles or a smooth wooden floor), attach the six included anti-slip pads (pieces of cork 1 mm thick) to the bottom. (Refer to diagram below. ) Anti-slip pad Anti-slip pad Base (ASF-T55) Screw holes (Mounting on the base ) The speaker system (SC-T55XG) can be mounted to a separately sold base (ASF-T55) using the four screw holes on the bottom. When doing so, follow the instructions included with the base and be very careful to mount the speaker system securely. The speaker system (SC-T55XG) comes with a part to prevent it from tipping over (stand attachment: 300 mm in length, mount screws: M4 x 40 mm). Line up the two holes on the back of the cabinet with the holes in the stand attachment, and use a screwdriver to securely fasten the mount screws. Screwdriver Stand attachment Screw Also, mount the stand attachment properly, as shown on the diagram below. Mounting it incorrect could result in the speaker system tipping over and causing injury or other serious accidents, so be very careful to mount correctly. Subjecting the stand attachment to excessive shocks when moving the speaker system with the stand attachment attached could result in damage. If anti-slip pads have already been attached to the bottom of the speaker system (SC-T55XG), apply the two anti-slip pads to the edges of the stand attachment. (Refer to diagram below. ) Anti-slip pad Anti-slip pad CONNECTIONS Before connecting, please consult with the instructions of your amplifier and follow them also. Be sure to turn the amplifier's power off when connecting the speaker systems. • Use the included cables to connect the input terminals on the back of the speaker systems (see diagram) to the amplifier's speaker output terminals. • Connect the speaker system for the left channel amplifier's "L" terminals, the one for the right channel to the amplifier's "R" terminals, matching the polarities (" " and " " marks). • Inverting the polarities will result in unnatural sound, with the phase off or no low bass sound. [. . . ] (When bi-wiring, we recommend using cords with excellent transfer characteristics. ) • The top set of input terminals are for the tweeter and super tweeter, the bottom set for the woofer. First loosen all the knobs, remove both short-circuit plates, then connect the speaker cords to the respective terminals. (See diagram next page. ) Be sure to remove both short-circuit plates. Twist the other ends (the sides to be connected to the amplifier) of the two cords for the " " side (red) together, and do the same for the two cords for the " " side (black). [. . . ]