ユーザーズガイド PANASONIC SJ-MJ10

[. . . ] The title of the disc or song is shown. The title scrolls if it can not be displayed all at once. Wired remote control ; Display < Hold switch (HOLD1) = Volume control buttons (i, j) > Play/stop button (1/∫) ?Skip/search(forward) button (9) @ Skip/search(backward) button (:) A Earphone jack B Light/display button ($LIGHT/ %DISP) C Play mode button (PLAY MODE) D Tone control/memory button (EQ/MEMORY) E Clip F Plug 4. Press [1/∫] to start play. The player stops when all the tracks on the disc have been played. 5. Adjust the volume. i: To increase the volume, j: To decrease the volume Volume level is 0–25. Stereo earphones G Plug H Slider Slide up to prevent entangling of the cord when not in use. ∫To stop the disc Press [1/∫]. The unit powers itself off in about 10 seconds. ∫Removing the disc Slide [OPEN 1] in the direction of the arrow and the disc springs out from the unit. Display information I Number of tracks/track number J Text/play time K Tone quality L Play mode M Battery indication ∫MDLP You can play tracks recorded with MDLP mode. The unit selects the play mode according to the recording mode: normal stereo, 2 kplay stereo (LP2), or 4kplay stereo(LP4). ∫Monaural playback If a disc was recorded monaurally, the unit switches to monaural mode. Power source Refer to the illustration on page 4, 5 of the other manual. ∫Resume function The player stores the point where you stop play and when you press [1/∫] again, play begins from that point. [. . . ] Scan the introductions of tracks and program a maximum of 24 tracks in the order you want to hear them. Selecting a group to a play Selecting a group to play When you have created groups on an MD with an MD recorder, you can start play from a specified group. Select a group by pressing and holding [:] or [9]while stopped. (Not possible while “MEMO” and “INTRO” is displayed. ) Forward : 9 Backward : : Program the tracks 1. While stopped, press [PLAY MODE] until “INTRO” appears. The unit powers itself off in about 30 seconds if you do not perform another operation. The first 10 seconds of each track are played in order (intro-scan). You can skip tracks during intro-scan. 2. Press [1/∫] to start play. Play starts from the selected group and plays through to the final track. 3. Press [EQ/MEMORY] while the track number is flashing to program the track. When the introduction of the last track is played, intro-scan starts again from the beginning. Tracks you have programmed are not played again. About the remote control Refer to the illustration on page 11 of the other manual. The display lights for about 5 seconds when an operation is done on the unit or remote control. It remains lit for up to 20 seconds while a track or disc name is scrolling on the display. 4. Repeat step 3 to program all the tracks you want. Press [1/∫] to finish programming. You can start play of the program by pressing [1/∫] while “MEMO” is on the display (about 10 seconds). ∫Checking the display Press [$LIGHT/ %DISP]. The display lights for 5 seconds. ∫To make a new program – Clear all tracks While stopped and “MEMO” is on the display, press and hold [EQ/MEMORY] for about 3 seconds. “CLEAR” is displayed and all tracks are cleared. “INTRO” appears on the display after this. Start from step 2. ∫Adjusting the display’s contrast When the unit is powered on 1. Press and hold [1/∫] on the main unit and press [i] or [j] on the remote control to adjust the contrast. i : darker, j : lighter ∫If “END” or “FULL” is displayed You cannot program any more tracks. END : you have programmed all tracks on the disc FULL : you have programmed the maximum of 24 tracks Programming ends 2 seconds after either of these is displayed. ∫Changing the remote control’s display Press and hold [$LIGHT/ %DISP]. Each time you press and hold the button: The display changes to show the track title, the group title, the disc title, the playing time of all tracks, total number of tracks, the track number and elapsed playing time. “MEMO” is displayed instead of the elapsed play time during program play. ∫To cancel intro scan Press [PLAY MODE] while stopped. (“INTRO” disappears, the time information is shown, and normal play is restored. ) Playing the program If “MEMO” is on the display, start from step 2. ∫The operation tone A tone sounds when you press a button on the remote control. To turn the tone off, press and hold [1/∫] until “Beep OFF” appears. [. . . ] ≥Set the volume on this unit to between 20 and 23. (It may not be possible to use the car stereo cassette adaptor with some systems because of its construction. ) Sound quality You can operate this function only with remote control. Press [EQ/ MEMORY] when the player is stopped or playing. Every time the button is pressed the mode changes and an indicator is shown on the display in the following order. XBS-1 Increases the power of the bass sounds. v TRAIN Reduces sounds that may annoy others when you are using the player in a public place. [. . . ]