ユーザーズガイド PANASONIC TY-PKX200S

[. . . ] Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. TQZH 422-2 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic Ceiling Mount Bracket. Contents Precautions with regard to safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Projection distance measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BSetting up the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BAttachment plate mounting hole sizes and preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BScrews tightening torques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BInstalling the brackets to the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 BSuspending the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Adjusting the installation angle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Precautions with regard to safety WARNING Ask a qualified technician or the place of purchase to carry out any installation work such as installing the projector to a ceiling. [. . . ] The projector is equipped with a zoom lens and the lens shift function. Check the allowable dimensions of the set up location before carrying out installation work. Ceiling L 147. 4 168. 8 (6 - 5/8") 52. 9 (2- 1/16 " ) (5- 25/ 32 " ) SH SW W H <Units: mm (˝)> Screen size (16:9) Diagonal length 1. 01 m(40˝) 1. 27 m(50˝) 1. 52 m(60˝) 1. 77 m(70˝) 2. 03 m(80˝) 2. 28 m(90˝) 2. 54 m(100˝) 3. 05 m(120˝) 3. 81 m(150˝) 5. 08 m(200˝) Projection distance (L) Width (SW) 0. 89 m(2´11˝) 1. 11 m(3´7˝) 1. 33 m(4´4˝) 1. 55 m(5´1˝) 1. 77 m(5´9˝) 1. 99 m(6´6˝) 2. 21 m(7´3˝) 2. 66 m(8´8˝) 3. 32 m(10´10˝) 4. 43 m(14´6˝) Height (SH) 0. 50 m(1´7˝) 0. 62 m(2´) 0. 75 m(2´5˝) 0. 87 m(2´10˝) 1. 00 m(3´3˝) 1. 12 m(3´8˝) 1. 24 m(4´) 1. 49 m(4´10˝) 1. 87 m(6´1˝) 2. 49 m(8´2˝) Wide (LW) 1. 2 m(3´11˝) 1. 5 m(4´11˝) 1. 8 m(5´10˝) 2. 1 m(6´10˝) 2. 4 m(7´10˝) 2. 7 m(8´10˝) 3. 1 m(10´2˝) 3. 7 m(12´1˝) 4. 6 m(15´1˝) 6. 2 m(20´4˝) Telephoto (LT) 2. 4 m(7´10˝) 3. 0 m(9´10˝) 3. 7 m(12´1˝) 4. 3 m(14´1˝) 4. 9 m(16´) 5. 5 m(18´) 6. 2 m(20´4˝) 7. 4 m(24´3˝) 9. 3 m(30´6˝) 12. 4 m(40´8˝) Centre of lens Top edge of screen: H -0. 07m–0. 57m (-2˝–1´10˝) -0. 08m–0. 7m (-3˝–2´3˝) -0. 10m–0. 85m (-3˝–2´9˝) -0. 11m–1. 0m (-4˝–3´3˝) -0. 13m–1. 13m (-5˝–3´8˝) -0. 15m–1. 27m (-5˝–4´2˝) -0. 16m–1. 4m (-6˝–4´7˝) -0. 19m–1. 68m (-7˝–5´6˝) -0. 24m–2. 11m (-9˝–9´2˝) -0. 32m–2. 81m (-1´–9´2˝) Centre of lens Right edge of screen: W 0. 22m–0. 67m (8˝–2´2˝) 0. 28m–0. 83m (11˝–2´8˝) 0. 33m–1. 00m (1´–3´3˝) 0. 39m–1. 16m (1´3˝–3´9˝) 0. 44m–1. 33m (1´5˝–4´4˝) 0. 50m–1. 49m (1´7˝–4´10˝) 0. 55m–1. 66m (1´9˝–5´5˝) 0. 67m–2. 0m (2´2˝–6´6˝) 0. 83m–2. 49m (2´8˝–8´2˝) 1. 11m–3. 32m (3´7˝–10´10˝) Setting-up dimensions which are not given in the above table can be calculated using the formulas below. Dimensions such as projection distances can be calculated from the screen diagonal length. (Units for calculations: m) Screen Width: SW=SDx0. 872 Screen Height: SH=SDx0. 490 Minimum Projection Distance: LW=1. 2244xSD-0. 056 Maximum Projection Distance: LT=2. 4449xSD-0. 056 NOTE: B The dimensions in the table above and the values obtained from the above formulas may contain slight errors. 4 Installation After checking the height, width and structure of the ceiling while referring to “Projection distance measurements” on page 4, determine the appropriate positions for setting up the screen and installing the projector. ■ Setting up the screen Set up the screen according to the specified method in a position which takes into account the projection distance and angle and the type of screen being used. ■ Attachment plate mounting hole sizes and preparation Make holes for inserting the bolts while referring to the attachment plate diagram. <Attachment plate diagram> (Dimensions from below) <Bolt mounting hole size> 65(2-9/16'') 160(6-9/32'') 140(5-1/2'') 120(4-23/32'') 113. 8(4-15/32'') Center of screen 52. 9 (2- 1/16'') 70(2-3/4'') To the screen 140 (5-1/2'') Four holes drilled to fit M8 bolts 103. 8(4-1/16'') 110(4-5/16'') 130(5-3/32'') 150(5-7/8'') 130 (5-3/32'') Unit:mm(˝) Install the attachment plate so that the bracket fixing screw is on the side opposite to the screen. NOTE: B If installing to a concrete structure, the sizes of the bolt mounting holes should match the sizes of the anchor nuts used. < Installation example > BInstalling to a wooden structure Nuts Spring washer Suspension bolt stay Flat washers Nuts Ceiling surface Suspension bolts (M8 or 5/16˝) To the screen Nuts Spring washers Flat washers Attachment plate About 5 mm (3/16˝) Bracket fixing screw Procedure: # Make holes in the ceiling surface for inserting the suspension bolts. The sizes of the holes in the ceiling should match the sizes of the mounting holes in the attachment plate. (Refer to the above illustration. ) $ Secure the suspension bolts. Check that the suspension bolt locations are strong enough to bear the full weight of the projector. If they are not strong enough, use reinforcements while giving full consideration to the required safety coefficient. % Secure the attachment plate to the suspension bolts. The ends of the suspension bolts should protrude from the nuts by about 5 mm. Be sure to use flat washers and spring washers when installing the attachment plate. NOTE: BInstall the attachment plate so that the bracket fixing screw is on the side opposite to the screen. BSuspension bolts, nuts, spring washers and flat washers should be purchased separately. 5 Installation (continued) < Installation example > BInstalling to a concrete structure Procedure: # Make holes in the ceiling surface for inserting the suspension bolts. Anchor nuts The sizes of the holes in the ceiling should match the sizes of the mounting holes in the attachment Concrete plate. BIf products are no longer being used, they should be dismantled and removed by a qualified technician as soon as possible. 6 ■ Installing the bracket to the projector Projector mount bracket Secure in four places # Place the projector upside-down on a piece of soft cloth or similar material, and then attach the projector mount bracket to the base of the projector using the four accessory screws with washer. Stabilizer brackets Secure in four places $ Install stabilizer brackets as shown in the illustration at left, and secure them with the four accessory screws with washers. NOTE: B Install the drop-prevention bracket for ceiling mounting which is included as an accessory with the projector. [. . . ] % Mount the anchoring nuts or curled plugs (M8 or 5/16˝) commercially-available onto a sturdy ceiling surface (at the position shown in the figure on the left). & Fit the loop of the bent-back wire rope over the anchoring part, slide the wire clip in the direction and secure it at a position where the loop will not become disengaged, and tighten the hexagonal head bolt. ' Use pliers to crimp the bent-back wire rope so that its end does not protrude from the clamping tube. Wire clips max. [. . . ]