ユーザーズガイド PHILIPS PT 720

[. . . ] - Water may leak from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver. - Do not use the shaver, adapter or any other part if it is damaged, as this may cause injury. Always replace a damaged adapter, charger or part with one of the original type. [. . . ] Charging - When the shaver is charging, the charging light flashes green. Battery fully charged - When the battery is fully charged, the charging light lights up green continuously. 30 minutes, the charging light goes out to save energy. Charging with the adapter 1 Put the small plug in the shaver. 2 Put the adapter in the wall socket. , The charging light shows the charging status of the shaver (see section ‘Charge indications’ in this chapter). 22 10 EnGlIsh Using the shaver Note:You can also use the shaver directly from the mains. shaving 1 Press the on/off button once to switch on the shaver. 2 Move the shaving heads over your skin. Make circular movements. - Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system. 3 Press the on/off button once to switch off the shaver. 4 Clean the shaver (see chapter ‘Cleaning and maintenance’). Trimming (PT860 only) You can use the trimmer to groom your sideburns and moustache. 3 Clean the trimmer with the short-bristled side of the cleaning brush. Brush up and down along the trimmer teeth. 4 Close the trimmer (‘ click’). Tip: For optimal trimming performance, lubricate the trimmer teeth with a drop of sewing machine oil every six months. 1 2 27 English 15 storage - Put the protection cap on the shaver every time you have used it, to prevent damage. Replacement For maximum shaving performance, we advise you to replace the shaving heads every two years. Replace damaged shaving heads right away. Only replace the shaving heads with original HQ8 Philips Shaving Heads. 1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit. 2 1 3 Pull the shaving unit off the shaver. 4 Turn the lock anticlockwise (1) and remove the retaining frame (2). 5 Remove the shaving heads and place new ones in the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 6 Put the retaining frame back into the shaving unit and turn the lock clockwise. 28 1 EnGlIsh  Insert the lug of the shaving unit into the slot in the top of the shaver (1). Then close the shaving unit (2). Note: If the shaving unit does not close smoothly, check if you have inserted the shaving heads properly and if the retaining frame is locked. Accessories The following accessories are available: - HQ8 Philips Shaving Heads - HQ110 Philips Shaving Head Cleaning Spray (not available in some countries) Environment - Do not throw away the appliance with the normal household waste at the end of their life, but hand them in at an official collection point for recycling. [. . . ] Guarantee restrictions The shaving heads (cutters and guards) are not covered by the terms of the international guarantee because they are subject to wear. 30 1 EnGlIsh Troubleshooting This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, contact the Consumer Care Centre in your country. Problem Possible cause Solution Replace the shaving heads (see chapter ‘Replacement’). The shaver does The shaving not shave as well heads are as it used to. Long hairs obstruct the shaving heads. Clean the shaving heads one by one (see section ‘Cleaning the shaving unit with the cleaning brush’ in chapter ‘Cleaning and maintenance’). Make sure that the projections of the shaving heads fit exactly into the recesses (see section ‘Cleaning the shaving unit with the cleaning brush’). [. . . ]