ユーザーズガイド ROLAND DAC-15

[. . . ] No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (separate sheet). [. . . ] Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Main Features * * A very solid and stable stand featuring ball clamps that allow precise adjustments for all pads and cymbals. Cables are inside the pipes, providing a clean look and quick breakdown or setup. Fully Assembled View • View of Stand When Spread Open Use the cable clips as shown below, to secure the cables. Components Cable clip A B 750 mm 600 mm C Cable Height memory Label D A B C D E F G H I J E F G H I J Sound module mounting pipe including the mounting plate Curved pipe L 750mm, Center pipe 600 mm (connection cables are inside) Curved pipe R Straight pipe 630 mm Straight pipe 650 mm L Straight pipe 650 mm R Straight pipe 500 mm Cymbal arm x 3 Pad arm x 4 Holder x 5 Drum key Owner´s manual (this lea et) Cable tie ** We recommend using an optional Roland drum mat (TDM series) to prevent scarring or discoloration of flooring by the rubber feet of the stand. Specifications • Required Space for Set-up 1, 400 (W) x 950 (D) x 1, 100 (H) mm / 55-1/8 (W) x 37-7/16 (D) x 43-5/16 (H) inches (Drum Stand only) 1, 600 (W) x 1, 400 (D) x 1, 250 (H) mm / 63 (W) x 55-1/8 (D) x 49-1/4 (H) inches (including Sound Module, Kick Pad, Cymbals and Stool) • Tube Diameter Stand: 38. 1 mm / 1-1/2 inches Pad Arm/Cymbal Arm: 22. 2 mm / 7/8 inches • Weight 20. 5 kg / 45 lbs 4 oz (including Pad Mounts and Cymbal Mounts) * In the interest of product improvement, the specifications and/ or appearance of this unit are subject to change without prior notice. Setting Up The Stand Important in Setting Up the Stand ** Make sure to firmly tighten all hand knobs and bolts after you have assembled the stand and attached any components. You should probably also try to make a habit of checking and retightening them if necessary before every performance. For about connections, refer to the owners manual that came with your sound module. The names on the labels correspond to trigger input jack names as follows. (input names shown here are for the TD-20X modules) Label Jack Label Jack KIK KICK CR1 CRASH1 SNR SNARE CR2 CRASH2 T1 TOM 1 RD RIDE T2 TOM 2 RDE EDGE T3 TOM 3 AX1 AUX 1 T4 TOM 4 AX2 AUX 2 HH HI-HAT AX3 AUX 3 HHC HH CTRL AX4 AUX 4 I H NOTE The factory setting of the rod angle is different only for the Tom 2 mount. I H 2 J B B 4 I H 1 5 E F J C I A 3 Working in order, following numbers 1–6 in the illustration, attach the curved pipes to the straight pipes. * Of pipes “B, ” the long one (750 mm) is Curved Pipe L, and the shorter one (600 mm) is the Center Pipe. [. . . ] * Of pipes “B, ” the long one (750 mm) is Curved Pipe L, and the shorter one (600 mm) is the Center Pipe. [. . . ]