ユーザーズガイド RYOBI ID700RE SCHEMA

[. . . ] To ensure accident-free operation, be sure to observe the following precautions. For Your Safety Explanation of Warning Indication The following indications are used in this manual and on the product. Understand these indications fully before reading the main text. DANGER Observe Safety Precautions Read the safety precautions carefully on page 3 to 6. General precautions for safety of this product are described. Read the “Precautions” on page 6 as well. [. . . ] • SAVE EXIT Saves the measurement results and exits the setting process. • RETRY Performs the Auto Calibration again. 2 Perform Auto Calibration again. Press V/v to select “RETRY YES”, then press . 3 Follow steps in “3: Confirming/saving the measurement results” (page 29). 3 Save the measurement result. Select “SAVE EXIT” in step 2. “COMPLETE” appears on the display panel and the measurement results are saved. 4 Disconnect the optimizer microphone from the receiver. Note If you reposition your speaker, we recommend that you perform Auto Calibration again to enjoy the surround sound. 29GB Checking the warning message If a warning on the measurement result is present, detailed information is displayed. Display and explanation W - xxx* 40 The measurement process has completed with high noise level detection. You may be able to achieve better results if you try in a quite environment again. W - xxx* 41 W - xxx* 42 The input from the microphone is too big. The distance between the speaker and the microphone may be too close. Set them apart and perform the measurement again. W - xxx* 43 The distance and position of a subwoofer cannot be detected. Try to perform the measurement in a quiet environment. NO WARN There is no warning information. Basic Operations Playback BD/DVD GAME SAT/ CATV VIDEO TV LINE IN Input buttons TUNER AMP MENU , V/v/B/b O m M X x > * xxx represent a speaker channel FL Front left FR Front right CNT Center SL Surround left SR Surround right SW Subwoofer Depending on the measurement result, the speaker channel may not appears. MASTER VOL +/– MUTING . SOUND FIELD +/– 1 2 3 Turn on the connected equipment. Press the input button which corresponds to the equipment you want. You can also use INPUT +/– on the receiver. Press V/v repeatedly until “TUNER” appears, then press or b. Press V/v repeatedly until “NAME IN” appears, then press or b. The cursor flashes and you can select a character. Repeat steps 2 to 5 to store another station. To change the preset number Restart from step 3. Tuning to preset stations 1 2 Press TUNER. Press PRESET + or PRESET – to select the station. Each time you press the button, you can select a preset station as follows: 1 2 3 30 4 29 5 28 . . . 27 6 Press V/v to select a character, then press B/b to move the input position backward and forward. You can enter up to 8 characters to name the station. Tips • You can select the character type as follows by pressing V/v. Alphabet (upper case) t Numbers t Symbols • To enter a blank space, press b without selecting a character. You can also hold down SHIFT and then press the numeric buttons to enter the preset station. To tune to the selection, hold down SHIFT then press ENTER. If you enter a wrong character Press B/b until the character to be changed flashes, then press V/v to select the desired character. 7 Press . The name you entered is registered. 34GB x A. F. D. Standard) Enjoying Surround Sound Selecting the sound field This receiver can create multi channel surround sound. You can select one of the optimized sound fields from the receiver’s pre-programmed sound fields. . X x > Presets the sound as it was recorded/encoded without adding any surround effects. However, this receiver will generate a low frequency signal for output to the subwoofer when there is no LFE signals. x A. F. D. [. . . ] • Check that the antennas are connected securely. Adjust the antennas and connect an external antenna (aerial), if necessary. • The signal strength of the stations is too weak with automatic tuning. • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations is used). [. . . ]