ユーザーズガイド SHARP LC-65GE1

[. . . ] LC-65GE1 Quick Start Guide in English An easy guide to basic features of this product 1 2 » 5 » 3 » » » 4 3 4 » » » » » 8 8 4 141 11 056 1 » 1 011-1 c 24 –– 2– 23 ––– 1–– 16– 162 » » » » » » » » » » » 3 1 2 3 ∫ ∫ ∫ 1 1 2 3 4 5 ∫ 6 ∫ 7 2 1 2 3 4 5 7 1 2 3 1 1 4 6 4 5 7 5 6 7 4 5 6 1 1 1 2 3 4 5 2 3 6 7 4 5 7 6 6 7 8 » » » » » Quick Start Guide in English Quick Start Guide in English Part Names Part Names — Remote Control Unit Basic Operations Enjoying Digital Broadcasts ! @ # 1 $ ! @ # @ $ 2 » » » » ! @ 1 # $ » » ! @ # @ $ » ||| • • • • • • • • • • • • • • • • • • • • • • • • • • » » ± — » » » » » » » OIL » » CL IN IC BAR » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » 5 1 151 1 » » » » » » » » » » » » » 1 ch900 1 11 1 1 2 3 4 5 6 7 » » » » » » » 1 » » » » » » » » » » » » » » » » » » » See page 36 if you wish to display menu screens in English. » » » » » 1 2 ! @ # » 3 $ ! @ # $ » ∫ ∫ » » » Switching the Display Language to English Using the menu screen, you can switch the on-screen display language to English. 1 !@ Operation Steps (Start) Press (menu) to display the menu screen. Press or to select (Setup). 1 # Language $ 2 # @ $ Press or Language press (enter). to select , then ! @ 2 » English MENU [Setup . . . [. . . ] • The remote sensor window on the display unit may not properly receive remote control signals when it is under direct sunlight or strong lighting. In such a case, change the angle of the lighting or the display unit. Cautions regarding batteries Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. • Do not mix batteries of different types. • Do not mix old and new batteries. CAUTION • Do not try to charge or disassemble batteries. • Place the batteries with their terminals corresponding to the ± and — indications. • Do not short-circuit batteries. Note • The supplied batteries may have a shorter life expectancy due to storage conditions. Replace them with new ones before they are depleted. • Remove the batteries from the remote control, if you do not use it for a long time. • If, after replacing batteries, the remote control does not work, make sure the new batteries are placed in the right direction. Quick Start Guide Basic Operations Shown on this and the next three pages are the basic operations for enjoying TV and video programs. Turning the power on !Press the (main power on/off) switch to turn on the power. » The TV set enters the standby mode (with the power indicator lit red) or the active mode (with the power indicator lit green). Side view of the display unit Bottom right corner of the display unit’s front side Standby mode Active mode Go to step @. Now you can operate the TV set using the remote control. Power indicator » When the power indicator flashes in red, check the system cable connection. @Engage the TV set in the active mode by performing any of the following operations. » Press the » Press the Remote control (active/standby) button on the remote control. (active/standby) button on the tuner unit. The power indicator will turn from red to green. Tuner unit Note » When you press the or (active/standby) button to turn off the TV, it may take a while before the power is actually turned off. (During this time, the system is storing the internal data to its memory. ) Power supply and power cable connection » The tuner unit communicates with digital TV stations even when it is in the standby mode. » Do not disconnect the power cable from the wall outlet immediately after it has been plugged in. In rare cases, the tuner unit’s memory will be initialized causing timer programs, the PPV program purchase history (unrecoverable), etc. If this happens, perform all necessary settings again. » Do not unplug the power cable or interrupt power supply when the TV set is in use. This may damage the data stored in the built-in memory. Quick Start Guide in English Quick Start Guide Basic Operations Power on/off, channel selection, volume control Turn on the TV. Power on ············ The power indicator (Active mode) lights green. Remote control Turn off the TV. Power off ············ The power (Standby mode) indicator lights red. Select the desired network. Network select buttons • Press to select the desired network (terrestrial analog [ ], terrestrial digital [ ], BS, or CS). (∗ The [terrestrial digital select] button works only after terrestrial digital broadcasting services are started in your area and the TV set is tuned to receive terrestrial digital broadcasts. ) Select the desired favorite channel. Favorite channel select /register • Press to select the userregistered channel. ( Press the favorite channel select/register ( ) button, then press the channel select button. ) Select the desired channel. Channel select buttons • Press to select a channel after selecting the desired network (terrestrial analog [ ], terrestrial digital [ ], BS, or CS) and media (TV, radio, or data). [. . . ] What you do first is to select the network of your choice. Press (terrestrial digital) , to select the desired network. or • Each time you press the CS button, the network changes as shown below. CS1 (SKY PerfecTV!110P) CS2 (SKY PerfecTV!110S) 2 Select the type of broadcast (Not necessary when selecting a channel by entering the channel number. ) Digital broadcasts offer not only TV programs but also radio and data programs. After you have selected the network of your choice in step radio, or data, by pressing 1 above, what you do next is to select the type of broadcast––TV, (media select). Press (media select) to select the desired media (TV, radio, or data). • Each time you press the button, the media changes as shown below. TV Radio Data Operating a data program screen Data programs usually display control button and item graphics on the screen. Use cursor buttons and (enter/confirm) as well as color buttons ( Blue Red ) to select Green Yellow an item, confirm your choice, or switch screens back and forth, etc. 3 Select the desired channel 1 Using the channel select buttons The channel select buttons are factory preset to receive the channels listed in the tables shown on page 210. After you have received the desired type of broadcast in step 2 above, all you do now is press one of the channel select buttons to directly select the channel of your choice. [. . . ]