ユーザーズガイド WACOM CINTIQ 21UX DTK-2100

[. . . ] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. [. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Checking for floppy. . . Bad BIOS checksum. Start flashing. . . 4-8 ® 4-9 4-10 4-11 System Time System Date Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information [11:10:19] [Tue, 06/29/2004] [English] [Maxtor 6Y080L0] [WACOM CDS520/] [Not Detected] [Not Detected] [Not Detected] [Not Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. 4-12 System Time System Date Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information [11:10:19] [Tue, 06/29/2004] [English] [Maxtor 6Y080L0] [WACOM CDS520/] [Not Detected] [Not Detected] [Not Detected] [Not Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. 4-13 System Time System Date Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information [11:10:19] [Tue, 06/29/2004] [English] [Maxtor 6Y080L0] [WACOM CDS520/] [Not Detected] [Not Detected] [Not Detected] [Not Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. 4-14 Primary IDE Master Device : Hard Disk Vendor : Maxtor 6Y080L0 Size : 81. 9GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : 4 Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-6 SMART Monitoring: Supported Type LBA/Large Mode Block (Multi-sector Transfer) PIO Mode DMA Mode Smart Monitoring 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] Select the type of device connected to the system. M 4-15 IDE Configuration Onboard IDE Operate Mode Enhanced Mode Support On IDE Detect Time Out (Sec) [Enhanced Mode] [S-ATA] [35] Set [Compatible Mode] when Legacy OS (i. e. Set [Enhanced Mode] when Native OS (i. e. WIN2000, WIN XP) is used. ® ® 4-16 AMI BIOS Version : 08. 00. 09 Build Date : 06/15/04 ID : A0103101 Processor Type Speed Count : Intel(R) Celeron(R) CPU 1. 70GHz : 1700MHz : 1 System Memory Size : 120MB 4-17 CPU Configuration Chipset Onboard Devices Configuration PCI PnP USB Configuration Load MiniLoader [Disabled] Configure CPU. Configure advanced CPU settings Manufacturer Brand String Frequency FSB Speed Cache L1 Cache L2 Cache L3 : Intel(R) : Intel(R) Celeron(R) 4 CPU 1. 70GHz : 1700MHz : 400MHz : 8 KB : 128 KB : 0 KB Sets the ration between CPU Core Clock and the FSB Freuency. Note: If an invalid ratio is set in CMOS, then actual and setpoint values may differ. Ratio Status : Locked Ratio Actual Value : 17 Max CPUID Value Limit [Disabled] 4-18 Advanced Chipset settings WARNING: Setting wrong values in the sections below may cause system to malfunction. [. . . ] Set [Enhanced Mode] when Native OS (i. e. WIN2000, WIN XP) is used. ® ® 4-16 AMI BIOS Version : 08. 00. 09 Build Date : 06/15/04 ID : A0103101 Processor Type Speed Count : Intel(R) Celeron(R) CPU 1. 70GHz : 1700MHz : 1 System Memory Size : 120MB 4-17 CPU Configuration Chipset Onboard Devices Configuration PCI PnP USB Configuration Load MiniLoader [Disabled] Configure CPU. Configure advanced CPU settings Manufacturer Brand String Frequency FSB Speed Cache L1 Cache L2 Cache L3 : Intel(R) : Intel(R) Celeron(R) 4 CPU 1. 70GHz : 1700MHz : 400MHz : 8 KB : 128 KB : 0 KB Sets the ration between CPU Core Clock and the FSB Freuency. Note: If an invalid ratio is set in CMOS, then actual and setpoint values may differ. Ratio Status : Locked Ratio Actual Value : 17 Max CPUID Value Limit [Disabled] 4-18 Advanced Chipset settings WARNING: Setting wrong values in the sections below may cause system to malfunction. [. . . ]