ユーザーズガイド YAMAHA CL1

[. . . ] 7. 8. 3. 4. 5. 38 6. 1. 7. 2. 3. 4. 5. 39 1. 2. 1. [. . . ] +48V DC ( phantom power ) is supplied to OMNI IN (1-8) and TALKBACK XLR type connectors via each individual software controlled switches. 55 Output Terminals OMNI OUT 1-8 PHONES *1. *6. Actual Source Impedance 75Ω 15Ω For Use With Nominal 600Ω Lines 8Ω Phones 40Ω Phones Output Level GAIN SW*5 +24dB (default) +18dB – – Nominal +4dBu (1. 23V) –2dBu (616mV) 75mW*6 65mW *6 Max. before clip +24dBu (12. 3V) +18dBu (6. 16V) 150mW 150mW Connector XLR-3-32 type (Balanced)*1 Stereo Phone Jack (TRS) (Unbalanced)*2 XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD) PHONES stereo phone jack is unbalanced. (Tip= LEFT, Ring= RIGHT, Sleeve= GND) In these specifications, 0dBu= 0. 775 Vrms. All output DA converters are 24bit, 128times oversampling. There are switches inside the body to preset the maximum output level. The position of the level control is 10dB lowered from Max. Terminal Primary/Secondary Format Dante Data length 24bit or 32bit Level 1000Base-T Audio 64ch Input/64ch Output @48kHz Connector EtherCON Cat5e Terminal DIGITAL OUT *1. AES/EBU Format AES/EBU Professional Use Data Length 24bit Level RS422 Connector XLR-3-32 type (Balanced)*1 XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD) Terminal MIDI WORD CLOCK GPI (5IN/5OUT) NETWORK LAMP (CL5: x3, CL3: x2, CL1: x1) USB HOST DC POWER INPUT METER (CL3/CL1 only) *1. IN OUT IN OUT Format MIDI MIDI – – – IEEE802. 3 – USB 2. 0 – – Level – – TTL/75Ω terminated TTL/75Ω – 10BASE-T/100Base-TX 0V-12V*4 – – – Connector DIN Connector 5P DIN Connector 5P BNC Connector BNC Connector D Sub Connector 15P (Female)*1 RJ-45 XLR-4-31 type*2 USB A Connector (Female) JL05 Connector D Sub Connector 9P (Female) *2. Input pins: TTL level inputs, It provides internal pull-up (47kΩ) Output pins: Open drain outputs, Maximum output voltage Vmax=12V, Maximum sink current per pin=75mA Power pins: Output voltage Vp=5V, Total maximum output current Imax=300mA 4pin= +12V, 3pin= GND, Lamp rating 5W. Voltage control by software. 56 4 9 15 20 14 19 8 3 7 13 18 23 2 6 12 17 22 1 5 11 16 21 10 8 3 2 1 15 11 10 9 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Signal Name +24V +24V +24V +24V +24V +24V +24V +24V +24V GND GND GND Pin 13 14 15 16 17 18 19 20 21 22 23 Signal Name GND GND GND GND GND GND CAUTION(+) CAUTION(–) DETECT A DETECT B DETECT GND Frame GND Pin 1 2 3 4 5 6 7 8 Signal Name GPO1 GPO3 GPO5 GND +5V GPI1 GPI3 GPI5 Pin 9 10 11 12 13 14 15 Signal Name GPO2 GPO4 GND GND +5V GPI2 GPI4 5 1 9 6 Pin 1 2 3 4 5 Signal Name RESET SDA DGND SCL +3. 3D Pin 6 7 8 9 Signal Name +3. 3LD +3. 3LD LDGND LDGND 57 15 299 201 1053 15 130 299 201 839 15 130 299 201 648 130 58 667 667 667 59 60 1. EQ (x4) DYN 1 DYN 2 INSERT DELAY DCA LEVEL /ON PAN BUS Adder INSERT ATT. EQ (x4) DYN MASTER LEVEL / BAL MASTER ON OUTPUT PATCH DELAY Digital 㱢㪃㪘㪫㪫㪃㩷 㪫㪩㪠㪤 DA Analog Analog dBu Digital GAIN dBFS Bit 㽲Max. [. . . ] 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. [. . . ]